Battery Aging Machine
Model No.: ACEY-CE-6008n
Battery type: Lithium battery pack
Warranty: 1 year
MOQ: 1 set
Package: Plywood Case
8 Channels 100V 60A High Voltage Battery Aging Machine Regenerative Battery Pack Tester System
Products Description
* Power battery simulation, C-rate test.
* Life cycle test.
* Power test, capacity test, energy density test.
* Power battery virtual distribution: charge/discharge curve fitting, battery consistency test and evaluation.
* High rate charge/discharge test.
* Power battery, serial energy-storage battery module test: single cell voltage, Single cell temperature monitoring(high-voltage equipment).
Specification
|
1、Model |
||
|
1. Material code |
ACEY-CE-6008n(100V60A-H) |
|
|
2、Channels information |
||
|
1. Channels quantity |
Channels quantity in one unit |
8 |
|
2. Main channel |
Channel feature |
Constant current source and constant voltage source dual closed loop control |
|
Channel control mode |
Independent control |
|
|
Channel parallel connection |
Support max 4 channels parallel mode. Pulse and SIM tests will be disabled in channels parallel mode. |
|
|
3、Power grid side parameters |
||
|
1.Input power |
AC380V±15% 50/60±5Hz |
|
|
2.Power factor |
≥99%(Full load) |
|
|
3.THDi |
≤5%(Full load) |
|
|
4.Input resistance |
≥1MΩ |
|
|
5.Input power |
56.5KW |
|
|
6.Input current |
85.8A/single |
|
|
7.Overall system efficiency(Max) |
90% |
|
|
8.Noise |
≤65dB |
|
|
9.Voltage and current sampling |
Four-wire connection(same port for charging and discharging) |
|
|
10.Power control module type |
MOSFET |
|
|
11.Input power wiring method |
Three-phase-five wire system |
|
|
12.Power input protection |
Anti-surge, anti-silos, anti over or under frequency, anti over or under voltage, anti phase absence, etc. |
|
|
4、Functions and performances |
||
|
1. Voltage |
Output range |
Charge:0V～100V |
|
Discharge:3V～100V |
||
|
Min discharge voltage |
3V |
|
|
Accuracy |
±0.02% of FS |
|
|
Resolution |
24bit |
|
|
2. Current |
Output range |
0.3A～60A |
|
Accuracy(independent range) |
±0.05% of FS |
|
|
CV cut-off current |
60mA |
|
|
Resolution |
24bit |
|
|
3. Power |
Single channel output power |
6KW |
|
Whole machine output power |
48KW |
|
|
4. Time |
Current response time |
≤3ms |
|
Current conversion time |
≤6ms |
|
|
Min. step time |
0.1s |
|
|
5. Charge/Discharge modes |
Charge/Discharge modes |
CCC, CVC, CC-CVC, CPC |
|
CCD, CVD, CPD, CRD |
||
|
Cut-off condition |
Voltage, Current, ΔTime, Capacity, -ΔV |
|
|
6. Simulation |
Charge |
Current, Power |
|
Discharge |
Current, Power |
|
|
Switch |
Support continuous switching between charge and discharge |
|
|
Cut-off condition |
Time, step line |
|
|
Steps file lines |
1,000,000 |
|
|
7. Pulse Mode |
Charge |
Current, power |
|
Discharge |
Current, Power |
|
|
Min pulse |
100ms |
|
|
Pulse counts |
Up to 32 |
|
|
Charge and discharge switch |
supported |
|
|
Cut-off condition |
Voltage, ΔTime |
|
|
8. DCIR |
|
DCIR by calculation |
|
9. Safely protection |
Software protection |
Power off data protection |
|
Offline mode function |
||
|
Safety protection conditions can be set, including: voltage lower limit, voltage upper limit, current lower limit, current upper limit, delay time, etc. |
||
|
Hardware protection |
Anti-reverse connection, over-voltage, over-current, over-temperature, etc. |
|
Product Details
Certifications
Cooperative Partner
Cim npe nrov: roj teeb laus tshuab
Koj Tseem Yuav Zoo Li
Xa kev nug